自動流體處理系統(AFHS)

Sample rate

4ml/min

Tubing materials

Translucent PTFE and Tygon®

Required desk space for Instrument

50cm (H) x 65cm (W) x 63cm (D)*

*XP Flame photometer with BWB

Recommended set up positioning.
For Safety reasons the Flame photometer
requires 1m of unobstructed space above to allow dissipation of
heat from the chimney.

Instrument size

XP Flame Photometer
51cm (H) x 38cm (W) x 41cm (D)
(20in x 14in x 16in)

Auto Diluter
30cm (H)  x 30cm (W) x 43cm (D)*
(12in x 12in x 17in)

Auto Sampler
30cm (H)  x 18cm (W) x 11cm (D)**
(12in x 7in x 4in)

Shipping
62cm (H) x 55cm (W) x 47cm (D)  x 2 boxes
(24in x 22in x 19in)

*Inclusive of Cannula operating arm.
** Excluding Dilution Reservoir.

Weight

XP Flame Photometer – 15.3kg (33.7lbs)
Auto Diluter – 3.75kg
Auto Sampler – 6.9kg

Shipping
XP Flame Photometer – 25kg
AFHS unit – 17kg

Amount of fluid used per sample
based on dilution ratios,

DR1 – 5.0ml
DR10  – 0.5ml
DR100 – 0.05ml

Specificity

Na/K/Li = <0.5% to each other when equal
in concentration at <100ppm

Optimal range

Single point calibration

Na 0.1 – 60ppm

K 0.05 – 100ppm

Li 0.05 – 50ppm

Ca 1.0 – 100ppm

Ba 1.6 – 100ppm

Multi Point Calibration

Na 0.1 – 1000ppm

K 0.05 – 1000ppm

Li 0.05 – 1000ppm

Ca 1.0 – 1000ppm

Ba 5.0 – 3000ppm

Reproducibility

<1% Coefficient of variability for 10 consecutive samples within
optimal range. (After instrument stabilisation).

Limit of detection (LOD) and
limit of quantification (LOQ) displayed

LOD                      LOQ

Na – 0.1ppm      Na – 0.3ppm

K – 0.05ppm      K – 0.15ppm

Li – 0.05ppm     Li – 0.15ppm

Ca – 1ppm          Ca – 3ppm

Ba – 1.6ppm      Ba – 15ppm

Time to stability

Less than 15 seconds after sample is introduced into the flame

Single sample time

With Auto Diluter: 130 Seconds including
Sample Preparation, Acquisition and flush

Without Auto Diluter: 80 Seconds including Acquisition and flush.

Amount of samples measured per hour

With Auto Diluter: 25
Without Auto Diluter: 40

Dilution reservoir size  
2.5L with inbuilt low level control standard.
5.0L available.

Amount of samples per dilution reservoir
2.5L – 120*       5L – 240*

*dependent on idle times between trays
and sample set-ups.

Amount of samples per tray  
89 with additional interchangeable trays
to speed up sampling time.

Interfaces

USB

0-2.5 volt output
(based on sample concentration linked to element of users choice)

Optional 4-20mA output in place of the above

Optional integrated printer

.csv and .pdf generated reports and files via FP-PC software

Recommended minimum warm up
time based on ambient temperature

21°C – 40 minutes

Power requirements

100V – 250V AC at 50 or 60Hz

Fuel requirement

Propane, Butane or Natural Gas*
regulated to 19Bar. Flow rate of 0.4l/min

*with modifications. BWB Technologies
recommends either Propane or Butane for
optimum results.

Readout

LCD, four line, alpha numeric, back lit.

Sample rate

4ml/min

Tubing materials

Translucent PTFE and Tygon®

Required desk space for Instrument

50cm (H) x 65cm (W) x 63cm (D)*

*XP Flame photometer with BWB

Recommended set up positioning.
For Safety reasons the Flame photometer
requires 1m of unobstructed space above to allow dissipation of
heat from the chimney.

Instrument size

XP Flame Photometer
51cm (H) x 38cm (W) x 41cm (D)
(20in x 14in x 16in)

Auto Diluter
30cm (H)  x 30cm (W) x 43cm (D)*
(12in x 12in x 17in)

Auto Sampler
30cm (H)  x 18cm (W) x 11cm (D)**
(12in x 7in x 4in)

Shipping
62cm (H) x 55cm (W) x 47cm (D)  x 2 boxes
(24in x 22in x 19in)

*Inclusive of Cannula operating arm.
** Excluding Dilution Reservoir.

Weight

XP Flame Photometer – 15.3kg (33.7lbs)
Auto Diluter – 3.75kg
Auto Sampler – 6.9kg

Shipping
XP Flame Photometer – 25kg
AFHS unit – 17kg

Amount of fluid used per sample
based on dilution ratios,

DR1 – 5.0ml
DR10  – 0.5ml
DR100 – 0.05ml

Specificity

Na/K/Li = <0.5% to each other when equal
in concentration at <100ppm

Optimal range

Single point calibration

Na 0.1 – 60ppm

K 0.05 – 100ppm

Li 0.05 – 50ppm

Ca 1.0 – 100ppm

Ba 1.6 – 100ppm

Multi Point Calibration

Na 0.1 – 1000ppm

K 0.05 – 1000ppm

Li 0.05 – 1000ppm

Ca 1.0 – 1000ppm

Ba 5.0 – 3000ppm

Reproducibility

<1% Coefficient of variability for 10 consecutive samples within
optimal range. (After instrument stabilisation).

Limit of detection (LOD) and
limit of quantification (LOQ) displayed

LOD                      LOQ

Na – 0.1ppm      Na – 0.3ppm

K – 0.05ppm      K – 0.15ppm

Li – 0.05ppm     Li – 0.15ppm

Ca – 1ppm          Ca – 3ppm

Ba – 1.6ppm      Ba – 15ppm

Time to stability

Less than 15 seconds after sample is introduced into the flame

Single sample time

With Auto Diluter: 130 Seconds including
Sample Preparation, Acquisition and flush

Without Auto Diluter: 80 Seconds including Acquisition and flush.

Amount of samples measured per hour

With Auto Diluter: 25
Without Auto Diluter: 40

Dilution reservoir size  
2.5L with inbuilt low level control standard.
5.0L available.

Amount of samples per dilution reservoir
2.5L – 120*       5L – 240*

*dependent on idle times between trays
and sample set-ups.

Amount of samples per tray  
89 with additional interchangeable trays
to speed up sampling time.

Interfaces

USB

0-2.5 volt output
(based on sample concentration linked to element of users choice)

Optional 4-20mA output in place of the above

Optional integrated printer

.csv and .pdf generated reports and files via FP-PC software

Recommended minimum warm up
time based on ambient temperature

21°C – 40 minutes

Power requirements

100V – 250V AC at 50 or 60Hz

Fuel requirement

Propane, Butane or Natural Gas*
regulated to 19Bar. Flow rate of 0.4l/min

*with modifications. BWB Technologies
recommends either Propane or Butane for
optimum results.

Readout

LCD, four line, alpha numeric, back lit.